Folgen
Antonio Sergio Pouzada
Antonio Sergio Pouzada
Institute for Polymers and Composites
Bestätigte E-Mail-Adresse bei dep.uminho.pt
Titel
Zitiert von
Zitiert von
Jahr
α-to β Transformation on PVDF Films Obtained by Uniaxial Stretch
V Sencadas, MV Moreira, S Lanceros-Méndez, AS Pouzada, ...
Materials science forum 514, 872-876, 2006
1742006
Friction properties on moulding thermoplastics
AS Pouzada, EC Ferreira, AJ Pontes
Polymer Testing 25 (8), 1017-1023, 2006
1142006
Structure–properties relationship in single polymer composites based on polyamide 6 prepared by in-mold anionic polymerization
N Dencheva, Z Denchev, AS Pouzada, AS Sampaio, AM Rocha
Journal of Materials Science 48, 7260-7273, 2013
612013
Hybrid moulds: effect of the moulding blocks on the morphology and dimensional properties
PG Martinho, PJ Bártolo, AS Pouzada
Rapid Prototyping Journal 15 (1), 71-82, 2009
592009
On the effect of the fiber orientation on the flexural stiffness of injection molded short fiber reinforced polycarbonate plates
NM Neves, G Isdell, AS Pouzada, PC Powell
Polymer composites 19 (5), 640-651, 1998
571998
Ejection force in tubular injection moldings. Part I: Effect of processing conditions
AJ Pontes, AS Pouzada
Polymer Engineering & Science 44 (5), 891-897, 2004
542004
The use of a three-point support flexural test to predict the stiffness of anisotropic composite plates in bending
JP Nunes, AS Pouzada, CA Bernardo
Polymer testing 21 (1), 27-33, 2002
542002
Hybrid moulds: A case of integration of alternative materials and rapid prototyping for tooling
AS Pouzada
Virtual and Physical Prototyping 4 (4), 195-202, 2009
502009
Microstructural characterization and mechanical properties of functionally graded PA12/HDPE parts by selective laser sintering
J Lisi Leite, GV Salmoria, RA Paggi, CH Ahrens, AS Pouzada
The International Journal of Advanced Manufacturing Technology 59, 583-591, 2012
442012
Ejection force of tubular injection moldings. Part II: A prediction model
AJ Pontes, AS Pouzada, R Pantani, G Titomanlio
Polymer Engineering & Science 45 (3), 325-332, 2005
412005
Chapter 9-Processing, Design, and Performance of Plastics Products
AS Pouzada
Gilbert, Marianne. Brydson's Plastics Materials (Eighth Edition), 205-46, 2017
40*2017
Chapter 6-Trends in the multifunctional performance of polyolefin/clay nanocomposite injection moldings
PM Frontini, AS Pouzada
Multifunctionality of Polymer Composites, 213-244, 2015
38*2015
Experimental assessment of hybrid mould performance
AJ Pontes, MP Queirós, PG Martinho, PJ Bártolo, AS Pouzada
The International Journal of Advanced Manufacturing Technology 50, 441-448, 2010
342010
Effect of LBM and large-area EBM finishing on micro-injection moulding surfaces
A Selada, A Manaia, MT Vieira, AS Pouzada
The International Journal of Advanced Manufacturing Technology 52, 171-182, 2011
322011
Analysis of friction in the ejection of thermoplastic mouldings
MS Correia, AS Miranda, MC Oliveira, CA Capela, AS Pouzada
The International Journal of Advanced Manufacturing Technology 59, 977-986, 2012
312012
The use of birefringence for predicting the stiffness of injection molded polycarbonate discs
NM Neves, AS Pouzada, JHD Voerman, PC Powell
Polymer Engineering & Science 38 (10), 1770-1777, 1998
301998
Microstructure of PP/clay nanocomposites produced by shear induced injection moulding
A Costantino, V Pettarin, J Viana, A Pontes, A Pouzada, P Frontini
Procedia Materials Science 1, 34-43, 2012
292012
Influence of hybridization of glass fiber and talc on the mechanical performance of polypropylene composites
CL Morelli, AS Pouzada, JA Sousa
Journal of applied polymer science 114 (6), 3592-3601, 2009
292009
Study of tribological properties of moulds obtained by stereolithography
MW Gonçalves, GV Salmoria, CH Ahrens, AS Pouzada
Virtual and Physical Prototyping 2 (1), 29-36, 2007
282007
Thermo-rheological behaviour of polymer melts in microinjection moulding
JC Vasco, JM Maia, AS Pouzada
Journal of Micromechanics and Microengineering 19 (10), 105012, 2009
272009
Das System kann den Vorgang jetzt nicht ausführen. Versuchen Sie es später erneut.
Artikel 1–20