Folgen
Benjamin Kirsch
Benjamin Kirsch
TU Kaiserslautern
Bestätigte E-Mail-Adresse bei mv.uni-kl.de - Startseite
Titel
Zitiert von
Zitiert von
Jahr
Engineering Science and Technology, an International Journal
M Eifler, F Schneider, J Seewig, B Kirsch, JC Aurich
Engineering Science and Technology, an International Journal 19, 1993-2001, 2016
143*2016
Sustainability of abrasive processes
JC Aurich, B Linke, M Hauschild, M Carrella, B Kirsch
CIRP Annals 62 (2), 653-672, 2013
1432013
Selective laser melting (SLM) of AISI 316L—impact of laser power, layer thickness, and hatch spacing on roughness, density, and microhardness at constant input energy density
S Greco, K Gutzeit, H Hotz, B Kirsch, JC Aurich
The International Journal of Advanced Manufacturing Technology 108, 1551-1562, 2020
1382020
Kinematic simulation of high-performance grinding for analysis of chip parameters of single grains
JC Aurich, B Kirsch
CIRP Journal of Manufacturing Science and Technology 5 (3), 164-174, 2012
1262012
Surface quality in micro milling: Influences of spindle and cutting parameters
JC Aurich, M Bohley, IG Reichenbach, B Kirsch
CIRP Annals 66 (1), 101-104, 2017
952017
Sustainability in ultra precision and micro machining: A review
F Schneider, J Das, B Kirsch, B Linke, JC Aurich
International Journal of Precision Engineering and Manufacturing-Green …, 2019
932019
Characterization of deformation induced surface hardening during cryogenic turning of AISI 347
JC Aurich, P Mayer, B Kirsch, D Eifler, M Smaga, R Skorupski
CIRP Annals-Manufacturing Technology 63 (1), 65-68, 2014
712014
Analytical and experimental investigations on the mechanisms of surface generation in micro grinding
D Setti, PA Arrabiyeh, B Kirsch, M Heintz, JC Aurich
International Journal of Machine Tools and Manufacture 149, 103489, 2020
652020
Improved coolant supply through slotted grinding wheel
JC Aurich, B Kirsch
CIRP Annals-Manufacturing Technology 62 (1), 363-366, 2013
632013
Investigation of wear resistance of dry and cryogenic turned metastable austenitic steel shafts and dry turned and ground carburized steel shafts in the radial shaft seal ring …
D Frölich, B Magyar, B Sauer, P Mayer, B Kirsch, JC Aurich, R Skorupski, ...
Wear 328, 123-131, 2015
572015
Application of ultra-small micro grinding and micro milling tools: Possibilities and limitations
B Kirsch, M Bohley, PA Arrabiyeh, JC Aurich
Micromachines 8 (9), 261, 2017
532017
Abrasive processes for micro parts and structures
JC Aurich, B Kirsch, D Setti, D Axinte, A Beaucamp, P Butler-Smith, ...
CIRP Annals 68 (2), 653-676, 2019
512019
Additive manufacturing of functionally graded Ti-Al structures by laser-based direct energy deposition
H Hotz, M Zimmermann, S Greco, B Kirsch, JC Aurich
Journal of Manufacturing Processes 68, 1524-1534, 2021
462021
Cutting edge preparation with elastic bonded superabrasive grinding wheels
JC Aurich, C Effgen, B Kirsch
CIRP Annals 65 (1), 329-332, 2016
402016
Analysis of the machinability when milling AlSi10Mg additively manufactured via laser-based powder bed fusion
M Zimmermann, D Müller, B Kirsch, S Greco, JC Aurich
The International Journal of Advanced Manufacturing Technology 112, 989-1005, 2021
392021
Manufacturing of structured surfaces via grinding
EJ Silva, B Kirsch, AC Bottene, A Simon, JC Aurich, JFG Oliveira
Journal of Materials Processing Technology 243, 170-183, 2017
382017
Sub-zero cooling: A novel strategy for high performance cutting
B Kirsch, S Basten, H Hasse, JC Aurich
CIRP Annals 67 (1), 95-98, 2018
372018
Influence of the macro-topography of grinding wheels on the cooling efficiency and the surface integrity
B Kirsch, JC Aurich
Procedia CIRP 13, 8-12, 2014
372014
Influence of the laser parameters on the cutting edge preparation and the performance of cemented carbide indexable inserts
M Zimmermann, B Kirsch, Y Kang, T Herrmann, JC Aurich
Journal of Manufacturing Processes 58, 845-856, 2020
362020
Intermethod comparison and evaluation of measured near surface residual stress in milled aluminum
CR Chighizola, CR D’Elia, D Weber, B Kirsch, JC Aurich, BS Linke, ...
Experimental Mechanics 61 (8), 1309-1322, 2021
342021
Das System kann den Vorgang jetzt nicht ausführen. Versuchen Sie es später erneut.
Artikel 1–20