| Microstructural, mechanical and tribological properties of Al–7Si–(0–5) Zn alloys Y Alemdağ, M Beder Materials & Design 63, 159-167, 2014 | 59 | 2014 |
| Effects of zinc content on strength and wear performance of Al− 12Si− 3Cu based alloy Y Alemdag, M Beder Transactions of Nonferrous Metals Society of China 29 (12), 2463-2471, 2019 | 32 | 2019 |
| Influence of Mg addition and T6 heat treatment on microstructure, mechanical and tribological properties of Al–12Si–3Cu based alloy M Beder, Y Alemdag Transactions of Nonferrous Metals Society of China 31 (8), 2208-2219, 2021 | 26 | 2021 |
| Dry sliding wear properties of Al-7Si-4Zn-(0-5) Cu alloys Y Alemdağ, M Beder Journal of the Balkan Tribological Association 21, 154-165, 2015 | 17 | 2015 |
| Effects of Mn content on microstructure, mechanical and dry sliding wear properties of eutectic Al–Si–Cu alloy Y Alemdag, M Beder Metals and Materials International 26, 1811-1819, 2020 | 15 | 2020 |
| The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy M Beder, SB Akçay, T Varol, H Çuvalcı Arabian Journal for Science and Engineering, 1-12, 2024 | 7 | 2024 |
| Impact of high Al2O3 content on the microstructure, mechanical properties, and wear behavior Al–Cu–Mg/Al2O3 composites prepared by mechanical milling M Beder, T Varol, SB Akçay Ceramics International 50 (20), 38610-38631, 2024 | 6 | 2024 |
| Influence of post processing on the mechanical properties and wear behavior of selective laser melted Co-Cr-Mo-W alloys T Varol, HC Aksa, F Yıldız, SB Akçay, G Kaya, M Beder Tribology International 192, 109336, 2024 | 6 | 2024 |
| Prediction of effect of fabrication parameters on the properties of B4C ceramic particle reinforced AA2024 matrix nanocomposites using neural networks T Varol, A Çanakçı, Ş Özşahin, M Beder, SB Akçay Materials Today Communications 39, 109279, 2024 | 4 | 2024 |
| Effect of age hardening on the wear behaviour of the Al-7Si-4Zn-3Cu alloy Y Alemdağ, G PÜRÇEK, M Beder 1st International Conference on Tribology (TURKEYTRIB'15), 7-9, 2015 | 1 | 2015 |
| The effect of high SiC ratio on the physical, mechanical, tribological and corrosion behavior of Al2024 alloy matrix composites fabricated by powder metallurgy M Beder, T Varol, SB Akçay, H Çuvalcı, F Erdemir, MA Khan, UT Yıldız Journal of Composite Materials, 00219983251316237, 2025 | | 2025 |
| The Effect of High B4C Ratio on the Improvement of Mechanical Properties and Wear Resistance of Al2024/B4C Composites Fabricated by Mechanical Milling-assisted Hot Pressing M Beder Ceramics International, 2025 | | 2025 |
| Toz metalurjisi yöntemiyle üretilen Al-Cu-Mg alaşımlarının mikroyapı ve tribolojik özelliklerinin incelenmesi M Beder Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi 14 (1), 1-1, 2025 | | 2025 |
| AlSi10Mg alaşımının içyapı ve mekanik özellikleri üzerine sıcak presleme yönteminin etkisi M Beder Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi 13 (4 …, 2024 | | 2024 |
| 添加 Mg 和 T6 热处理对 Al-12Si-3Cu 基合金显微组织, 力学性能和摩擦学性能的影响 (英文) M BEDER, Y ALEMDAG Transactions of Nonferrous Metals Society of China, 2021 | | 2021 |
| Zn 含量对 Al-12Si-3Cu 合金强度和磨损性能的影响 (英文) Y ALEMDAG, M BEDER Transactions of Nonferrous Metals Society of China 12, 2019 | | 2019 |
| Çözündürme ve Yaşlandırma İşleminin Al-7Si-4Zn-3Cu Alaşımının Sürtünme ve Aşınma Özelliklerine Etkisi Y Alemdağ, M Beder International Journal of Engineering Research and Development 11 (2), 602-611, 2019 | | 2019 |
| Çinko ve bakır katkılarının Al-7Si alaşımının yapı, mekanik ve tribolojik özelliklerine etkilerinin incelenmesi M Beder Fen Bilimleri Enstitüsü, 2014 | | 2014 |
| Sıcak presleme yöntemiyle üretilen AlSi10Mg alaşımının farklı presleme sıcaklıklarındaki yapı ve mekanik özelliklerinin incelenmesi M Beder Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi, 0 | | |
| Çinko, mangan ve magnezyum katkılarının Al-12Si-3Cu esaslı alaşımın yapı, mekanik ve tribolojik özelliklerine etkilerinin incelenmesi M Beder Fen Bilimleri Enstitüsü, 0 | | |
Yasin AlemdağVerified email at ktu.edu.tr
