Volgen
Mahfudz Al Huda
Mahfudz Al Huda
National Research and Innovation Agency, BRIN
Geverifieerd e-mailadres voor brin.go.id
Titel
Geciteerd door
Geciteerd door
Jaar
Temperature measurement of CBN tool in turning of high hardness steel
T Ueda, M Al Huda, K Yamada, K Nakayama, H Kudo
CIRP Annals 48 (1), 63-66, 1999
1251999
Investigation of temperature at tool-chip interface in turning using two-color pyrometer
M Al Huda, K Yamada, A Hosokawa, T Ueda
J. Manuf. Sci. Eng. 124 (2), 200-207, 2002
742002
Building digital-twin virtual machining for milling chatter detection based on VMD, synchro-squeeze wavelet, and pre-trained network CNNs with vibration signals
K Jauhari, AZ Rahman, M Al Huda, A Widodo, T Prahasto
Journal of Intelligent Manufacturing 35 (7), 3083-3114, 2024
142024
An intelligent milling chatter detection method based on VMD-synchro-squeeze wavelet and transfer learning via deep CNN with vibration signals
K Jauhari, AZ Rahman, M Al Huda, A Widodo, T Prahasto
The International Journal of Advanced Manufacturing Technology 129 (1-2 …, 2023
82023
Correlation analysis of vibration signal frequency with tool wear during the milling process on martensitic stainless steel material
AZ Rahman, K Jauhari, M Al Huda, NA Untariyati, M Azka, R Rusnaldy, ...
Arabian Journal for Science and Engineering 49 (8), 10573-10586, 2024
72024
Influence of tool posture and position on stability in milling with parallel kinematic machine tool
M Azka, K Yamada, MA Huda, R Tanaka, K Sekiya
International Journal of Precision Engineering and Manufacturing 21, 2359-2373, 2020
72020
Hilbert-Huang transform analysis of machining stability in ball-nose end-milling of curved surface
M Azka, K Yamada, M Al Huda, K Mani, R Tanaka, K Sekiya
International Journal of Automation Technology 14 (3), 500-511, 2020
72020
A novel method for analyzing electric field distribution of electro capacitive cancer treatment (ECCT) using wire mesh electrodes: A case study of brain cancer therapy
L Andiani, MAH Endarko, WP Taruno
Euromediterranean Biomedical Journal 12 (38), 178-183, 2017
72017
Optimization of phase shift-based capacitive sensor for water content detection in biodiesel
N Suryana, M Al Huda, O Choirunnisak, AE Mulyono, RD Samanhudi, ...
IEEE Sensors Journal 22 (16), 16131-16140, 2022
62022
Human brain auditory activity observation using electrical capacitance volume tomography
FF Darmawan, D Arifianto, MA Huda, WP Taruno
2017 IEEE sensors, 1-3, 2017
62017
Gas holdup and bubble flow transition characteristics in column flotation process determined by capacitive signals measurement
S Harjanto, D Haryono, H Nugraha, G Saputra, MR Baidillah, M Al Huda, ...
Brazilian Journal of Chemical Engineering 38 (2), 361-372, 2021
52021
Modeling of Deep Learning Applications for Chatter Detection in the Milling Process
K Jauhari, AZ Rahman, M Al Huda, M Azka, A Widodo, T Prahasto, ...
Procedia CIRP 118, 471-476, 2023
42023
Column flotation monitoring based on electrical capacitance volume tomography: A preliminary study
D Haryono, S Harjanto, H Nugraha, MA Huda, WP Taruno
AIP Conference Proceedings 1805 (1), 2017
42017
The effect of flotation reagents addition (MIBC and PAX) on the relative permittivity value using 2-electrode capacitance sensor
D Haryono, H Nugraha, M Al Huda, WP Taruno, S Harjanto
Procedia engineering 170, 369-372, 2017
42017
Flaw Detection in Welded Metal Using Magnetic Induction Tomography
D Sutisna, S Ullum, WP Taruno, AAS Iman, MR Baidillah, M Al Huda, ...
Advanced Materials Research 896, 722-725, 2014
42014
Enhancing Turbine Blade Manufacturing through MEMS-Based Milling Monitoring
AZ Rahman, K Jauhari, M Al Huda, D Sumantri, T Prahasto, A Widodo
IOP Conference Series: Earth and Environmental Science 1344 (1), 012016, 2024
32024
Analisis sensor kapasitif pelat sejajar pada aplikasinya sebagai deteksi zat satu fasa dan multi fasa
FM Rabbani, E Yuniarti, M Al-Huda
Komunikasi Fisika Indonesia 17 (2), 62-67, 2020
32020
The effects of feed rate to dimensional accuracy and roughness on machining process of propeller blade using 5-Axis CNC turn-milling machine
AZ Rahman, K Jauhari, H Suryaputra, M Abubakar, ET Wibowo, ...
International Journal of Applied Engineering Research 12 (24), 14989-14992, 2017
32017
Analisis Pengendalian Cacat Produk pada Proses Plastic Injection Molding dengan Material Polyprophylene
D Cahyadi, M Al Huda
TEKNOBIZ: Jurnal Ilmiah Program Studi Magister Teknik Mesin 1 (2), 79-87, 2011
32011
旋削加工における工具―切りくず接触面温度の測定
M Al Huda, 山田啓司, 上田隆司
日本機械学会論文集 65, 633, 1999
31999
Het systeem kan de bewerking nu niet uitvoeren. Probeer het later opnieuw.
Artikelen 1–20