| Review on design and structural optimisation in additive manufacturing: Towards next-generation lightweight structures J Plocher, A Panesar Materials & Design 183, 108164, 2019 | 660 | 2019 |
| Insights into the mechanical properties of several triply periodic minimal surface lattice structures made by polymer additive manufacturing I Maskery, L Sturm, AO Aremu, A Panesar, CB Williams, CJ Tuck, ... Polymer 152, 62-71, 2018 | 615 | 2018 |
| Strategies for functionally graded lattice structures derived using topology optimisation for additive manufacturing A Panesar, M Abdi, D Hickman, I Ashcroft Additive manufacturing 19, 81-94, 2018 | 574 | 2018 |
| An investigation into reinforced and functionally graded lattice structures I Maskery, A Hussey, A Panesar, A Aremu, C Tuck, I Ashcroft, R Hague Journal of Cellular Plastics 53 (2), 151-165, 2017 | 330 | 2017 |
| A voxel-based method of constructing and skinning conformal and functionally graded lattice structures suitable for additive manufacturing AO Aremu, JPJ Brennan-Craddock, A Panesar, IA Ashcroft, RJM Hague, ... Additive Manufacturing 13, 1-13, 2017 | 268 | 2017 |
| Effect of density and unit cell size grading on the stiffness and energy absorption of short fibre-reinforced functionally graded lattice structures J Plocher, A Panesar Additive Manufacturing 33, 101171, 2020 | 195 | 2020 |
| 3D printing to enable multifunctionality in polymer-based composites: A review DG Bekas, Y Hou, Y Liu, A Panesar Composites Part B: Engineering 179, 107540, 2019 | 195 | 2019 |
| Optimisation of blended bistable laminates for a morphing flap AS Panesar, PM Weaver Composite Structures 94 (10), 3092-3105, 2012 | 111 | 2012 |
| Design framework for multifunctional additive manufacturing: coupled optimization strategy for structures with embedded functional systems A Panesar, I Ashcroft, D Brackett, R Wildman, R Hague Additive Manufacturing 16, 98-106, 2017 | 74 | 2017 |
| Design framework for multifunctional additive manufacturing: placement and routing of three-dimensional printed circuit volumes A Panesar, D Brackett, I Ashcroft, R Wildman, R Hague Journal of Mechanical Design 137 (11), 111414, 2015 | 62 | 2015 |
| An experimental analysis of deepest bottom-left-fill packing methods for additive manufacturing LJP Araújo, A Panesar, E Özcan, J Atkin, M Baumers, I Ashcroft International Journal of Production Research 58 (22), 6917-6933, 2020 | 42 | 2020 |
| Investigation of thermally induced bistable behaviour for tow-steered laminates AS Panesar, K Hazra, PM Weaver Composites Part A: Applied Science and Manufacturing 43 (6), 926-934, 2012 | 42 | 2012 |
| Hierarchical remeshing strategies with mesh mapping for topology optimisation A Panesar, D Brackett, I Ashcroft, R Wildman, R Hague International Journal for Numerical Methods in Engineering 111 (7), 676-700, 2017 | 40 | 2017 |
| Mechanical performance of additively manufactured fiber-reinforced functionally graded lattices J Plocher, A Panesar Jom 72 (3), 1292-1298, 2020 | 24 | 2020 |
| Machine learning based lattice generation method derived from topology optimisation J Wang, A Panesar Additive Manufacturing 60, 103238, 2022 | 19 | 2022 |
| Optimized microstructures for multifunctional structural electrolytes C Lee, ES Greenhalgh, MSP Shaffer, A Panesar Multifunctional Materials 2 (4), 045001, 2019 | 17 | 2019 |
| Design optimization strategy for multifunctional 3d printing A Panesar, D Brackett, I Ashcroft, R Wildman, R Hague University of Texas at Austin, 2014 | 17 | 2014 |
| An optimization based design framework for multi-functional 3D printing D Brackett, A Panesar, I Ashcroft, R Wildman, R Hague University of Texas at Austin, 2013 | 13 | 2013 |
| Additive manufacturing with fibre-reinforcement–design guidelines and investigation into the influence of infill patterns J Plocher, JB Wioland, AS Panesar Rapid Prototyping Journal 28 (7), 1241-1259, 2022 | 12 | 2022 |
| Effect of manufacture-induced interfaces on the tensile properties of 3D printed polyamide and short carbon fibre-reinforced polyamide composites Y Hou, A Panesar Polymers 15 (3), 773, 2023 | 10 | 2023 |
Richard HagueProfessor, University of Nottingham - Additive ManufacturingZweryfikowany adres z nottingham.ac.uk