Fatigue behaviour of Zn–Al casting alloys

Turnitin 降AI改写 早检测系统 早降重系统 Turnitin-UK版 万方检测-期刊版 维普编辑部版 Grammarly检测 Paperpass检测 checkpass检测 PaperYY检测

Effect of copper content on the mechanical and sliding wear properties of monotectoid-based zinc-aluminium-copper alloys

T Savaşkan, AP Hekimoğlu, G Pürçek - Tribology International, 2004 - Elsevier
One binary zinc-aluminium monotectoid and five ternary zinc-aluminium-copper alloys were
produced by permanent mould casting. Their wear properties were examined using a block …
Сачувај Цитирај 191 пута наведен Сродни чланци Све верзије (6)

Machinability characteristics in Zn-40Al alloy: The effect of addition of copper and silicon and optimization of cutting parameters using response surface methodology

Ş Bayraktar, G Pehli̇van - Journal of Alloys and Compounds, 2025 - Elsevier
In this study, the impacts of Cu and Si additions to Zn-40Al alloy on its microstructural,
mechanical and machinability properties were investigated in the turning process. Zn-40Al …
Сачувај Цитирај 2 пута наведен Сродни чланци Све верзије (2)

Relationships between cooling rate, copper content and mechanical properties of monotectoid based Zn–Al–Cu alloys

T Savaşkan, MŞ Turhal - Materials Characterization, 2003 - Elsevier
One binary Zn–40Al and four ternary Zn–40Al–(1, 2, 3, 4) Cu alloys were produced by
permanent mould casting at different pouring and mould temperatures. Cooling curves were …
Сачувај Цитирај 94 пута наведен Сродни чланци Све верзије (7)

Relationships between secondary dendrite arm spacing and mechanical properties of Zn-40Al-Cu alloys

MŞ Turhal, T Savaşkan - Journal of materials science, 2003 - Springer
Three ternary monotectoid-based Zn-40Al-(1, 2, 3%) Cu alloys were produced by permanent
mould casting at different pouring and mould temperatures. The average cooling rate for …
Сачувај Цитирај 85 пута наведен Сродни чланци Све верзије (10)

Improvement of mechanical properties for Zn–Al alloys using equal-channel angular pressing

G Pürçek - Journal of Materials Processing Technology, 2005 - Elsevier
Multi-pass equal-channel angular pressing (ECAP) was applied to a commercially used zinc–
aluminum alloy (ZA-12) at a temperature of about 75° C by using route Bc, where the sample …
Сачувај Цитирај 93 пута наведен Сродни чланци Све верзије (5)

Hot tensile and fatigue behaviour of zinc–aluminum alloys produced by gravity and squeeze casting

F Cay, SC Kurnaz - Materials & design, 2005 - Elsevier
The tensile and fatigue properties of zinc–aluminum alloys (ZA-8, ZA-12 and ZA-27) in
squeeze and gravity cast forms have been investigated. Tensile tests were conducted at …
Сачувај Цитирај 71 пута наведен Сродни чланци Све верзије (4)

Effects of silicon content on the mechanical properties and lubricated wear behaviour of Al–40Zn–3Cu–(0–5) Si alloys

Y Alemdağ, T Savaşkan - Tribology Letters, 2008 - Springer
In this work, one ternary Al–40Zn–3Cu and seven quaternary Al–40Zn–3Cu–(0.25–5) Si
alloys were synthesized by permanent mould casting. Their microstructure, mechanical and …
Сачувај Цитирај 58 пута наведен Сродни чланци Све верзије (5)

Fatigue behaviour of monotectoid-based Zn–Al–Cu alloys in 3.5% NaCl and 1% HCl solutions

T Savaşkan, M Aydin - Materials characterization, 2004 - Elsevier
One binary Zn–40Al and three Zn–40Al-based ternary alloys containing 1%, 3%, and 5% Cu
were produced by permanent mold casting. Their fatigue behavior was investigated in 3.5 …
Сачувај Цитирај 41 пута наведен Сродни чланци Све верзије (4)

Fatigue properties of zinc–aluminium alloys in 3.5% NaCl and 1% HCl solutions

M Aydın, T Savaşkan - International journal of fatigue, 2004 - Elsevier
A series of binary zinc–aluminium alloys were produced by permanent mould casting.
Fatigue behaviour of the alloys was investigated in 3.5% NaCl and 1% HCl solutions using a …
Сачувај Цитирај 31 пута наведен Сродни чланци Све верзије (4)

Fatigue behaviour of Al–25Zn–3Cu alloy

T Savaşkan, HO Tan - Materials Science and Technology, 2014 - journals.sagepub.com
In the present study, Al–25Zn–3Cu alloy was prepared by permanent mould casting. Fatigue
behaviour of the alloy was investigated using a rotating bending fatigue test machine after …
Сачувај Цитирај 13 пута наведен Сродни чланци Све верзије (5)