High power pulsed magnetron sputtering: A review on scientific and engineering state of the art
High power pulsed magnetron sputtering (HPPMS) is an emerging technology that has
gained substantial interest among academics and industrials alike. HPPMS, also known as …
gained substantial interest among academics and industrials alike. HPPMS, also known as …
Oxidation protection of γ-TiAl-based alloys–a review
R Pflumm, S Friedle, M Schütze - Intermetallics, 2015 - Elsevier
Alloys based on γ-TiAl are lightweight materials with attractive mechanical properties at high
temperatures. Although these alloys reveal a superior resistance against environmental …
temperatures. Although these alloys reveal a superior resistance against environmental …
Oxidation resistance of TiN, CrN, TiAlN and CrAlN coatings deposited by lateral rotating cathode arc
In this paper, four kinds of hard coatings, TiN, CrN, TiAlN and CrAlN (with Al/Ti or Al/Cr
atomic ratio around 1: 1), were deposited on stainless steel substrates by a lateral rotating …
atomic ratio around 1: 1), were deposited on stainless steel substrates by a lateral rotating …
Concepts for the design of advanced nanoscale PVD multilayer protective thin films
M Stueber, H Holleck, H Leiste, K Seemann… - Journal of Alloys and …, 2009 - Elsevier
Technological challenges in future surface engineering applications demand continuously
new material solutions offering superior properties and performance. Concepts for the …
new material solutions offering superior properties and performance. Concepts for the …
Corrosion resistance of CrAlN and TiAlN coatings deposited by lateral rotating cathode arc
X Ding, ALK Tan, XT Zeng, C Wang, T Yue, CQ Sun - Thin Solid Films, 2008 - Elsevier
In this work, CrAlN and TiAlN coatings were deposited on stainless steel substrates by a
vacuum arc reactive deposition process from two lateral rotating elemental aluminum and …
vacuum arc reactive deposition process from two lateral rotating elemental aluminum and …
Influence of thickness on adhesion of nanostructured multilayer CrN/CrAlN coatings to stainless steel substrate
M Falsafein, F Ashrafizadeh, A Kheirandish - Surfaces and Interfaces, 2018 - Elsevier
Adhesion and load-bearing capacity are the two key factors that determine the final
performance of a coating, nevertheless, the adhesion of PVD coatings to stainless steel is …
performance of a coating, nevertheless, the adhesion of PVD coatings to stainless steel is …
Comparative analysis of cutting properties and nature of wear of carbide cutting tools with multi-layered nano-structured and gradient coatings produced by using of …
SN Grigoriev, AA Vereschaka, SV Fyodorov… - … International Journal of …, 2017 - Springer
The aim of this work was to investigate mechanical and cutting properties, as well as the
nature of wear and failure of carbide cutting tools with modifying coatings of two types: nano …
nature of wear and failure of carbide cutting tools with modifying coatings of two types: nano …
Wear performance of different PVD coatings during hard wet end milling of H13 tool steel
Wear performance of end mill tools with different PVD coatings has been studied under the
condition of hard wet machining of H13 tool steel. It was shown that tool life of the coated …
condition of hard wet machining of H13 tool steel. It was shown that tool life of the coated …
Structure, elastic properties and phase stability of Cr1–xAlxN
The effect of composition and metal sublattice population on the phase stability, structure
and elastic properties of cubic (c), hexagonal (h) and orthorhombic spin-polarized Cr1 …
and elastic properties of cubic (c), hexagonal (h) and orthorhombic spin-polarized Cr1 …
Mechanical properties and oxidation behaviour of (Al, Cr) N and (Al, Cr, Si) N coatings for cutting tools deposited by HPPMS
K Bobzin, N Bagcivan, P Immich, S Bolz, R Cremer… - Thin Solid Films, 2008 - Elsevier
Hard coatings with high hardness, high oxidation resistance and thermal stability are used
for economical machining. In this regard nanostructured (Cr, Al) N and nc-(Cr, Al) N/a-Si3N4 …
for economical machining. In this regard nanostructured (Cr, Al) N and nc-(Cr, Al) N/a-Si3N4 …