Turnitin
降AI改写
早检测系统
早降重系统
Turnitin-UK版
万方检测-期刊版
维普编辑部版
Grammarly检测
Paperpass检测
checkpass检测
PaperYY检测
Dynamic transformation during the high temperature deformation of titanium alloys
Dynamic transformation was first predicted by Gegel and Nadiv during hot deformation of a
Ti-6Al-2Sn-4Zr-2Mo alloy. Later it was observed in near alpha and two-phase titanium …
Ti-6Al-2Sn-4Zr-2Mo alloy. Later it was observed in near alpha and two-phase titanium …
Development of low-cost titanium alloys: A chronicle of challenges and opportunities
The production of titanium alloys became fully commercialized in the 1950s and that was
precisely 145 years since titanium ores, ilmenite and rutile were first discovered. In the …
precisely 145 years since titanium ores, ilmenite and rutile were first discovered. In the …
Understanding the microstructure evolution and mechanical behavior of titanium alloy during electrically assisted plastic deformation process
Titanium alloys are widely used in aerospace, petrochemical, and automobile industry due
to their outstanding mechanical properties. However, the formability/plasticity of most …
to their outstanding mechanical properties. However, the formability/plasticity of most …
Characterization of microstructure and mechanical properties of laser melting deposited Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si titanium alloy
Y Zhu, D Liu, X Tian, H Tang, H Wang - Materials & Design (1980-2015), 2014 - Elsevier
Abstract A plate of Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si (TC11) titanium alloy is fabricated by laser
melting deposition process. Grain morphology and microstructure characteristics and the …
melting deposition process. Grain morphology and microstructure characteristics and the …
Incorporating dynamic recrystallization into a crystal plasticity model for high-temperature deformation of Ti-6Al-4V
During hot deformation of (α+ β) titanium alloys, the simultaneous action of strain and
temperature in the (α+ β) regime facilitates dynamic recovery, dynamic recrystallization …
temperature in the (α+ β) regime facilitates dynamic recovery, dynamic recrystallization …
Characterization of hot deformation behavior of a new near beta titanium alloy: Ti-7333
The hot deformation behavior of Ti-7333 titanium alloy in the temperature range of 770–970°
C and strain rate range of 10− 3-10 s− 1 has been investigated by hot compressive testing …
C and strain rate range of 10− 3-10 s− 1 has been investigated by hot compressive testing …
High-temperature deformation behavior of Ti60 titanium alloy
Isothermal compressions of near-alpha Ti60 alloy were carried out on a Gleeble-3800
simulator in the temperature range of 960–1110° C and strain rate range of 0.001–10.0 s− 1 …
simulator in the temperature range of 960–1110° C and strain rate range of 0.001–10.0 s− 1 …
Special interlayer pause strategy for controlling grain morphology and tensile property anisotropy of TC11 alloys fabricated by directed energy deposition technology
K Wang, Z Fang, H Li, S Yang - Materials Science and Engineering: A, 2024 - Elsevier
Directed energy deposition (DED)-built titanium alloys have long suffered from the
anisotropic mechanical properties induced by the long columnar prior β grains growing …
anisotropic mechanical properties induced by the long columnar prior β grains growing …
Flow stress constitutive relationship between lamellar and equiaxed microstructure during hot deformation of Ti-6Al-4V
The mechanical properties of Ti–6Al–4V alloy are very sensitive to its microstructure
morphology. Commercially available Ti–6Al–4V was heat treated above and below the β …
morphology. Commercially available Ti–6Al–4V was heat treated above and below the β …
Ultrafine grain formation in a Ti-6Al-4V alloy by thermomechanical processing of a martensitic microstructure
In the current study, ultrafine equiaxed grains with a size of 150 to 800 nm were successfully
produced in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting …
produced in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting …