Issues in fabrication of 3D components through DMLS Technique: A review
Abstract DMLS or Direct Metal Laser Sintering is a technique which can be classified under
an additive manufacturing (AM). In this technique, metal powders are used to manufacture …
an additive manufacturing (AM). In this technique, metal powders are used to manufacture …
A two-decade odyssey in fusion-based additive manufacturing of titanium alloys and composites
SO Agbedor, H Wu, Y Ren, L Liang, DH Yang… - Applied Materials …, 2024 - Elsevier
In the past two decades, the advent of metal additive manufacturing (AM) or three-
dimensional (3D) printing technology has led to exciting breakthroughs in the metallurgy of …
dimensional (3D) printing technology has led to exciting breakthroughs in the metallurgy of …
Processing, mechanical characterization, and micrography of 3D-printed short carbon fiber reinforced polycarbonate polymer matrix composite material
The objective of this research is to perform the processing and mechanical characterization
on 3D-printed high-temperature polymer (polycarbonate) reinforced with short carbon fiber …
on 3D-printed high-temperature polymer (polycarbonate) reinforced with short carbon fiber …
Mechanical properties and corrosion resistance of laser cladding iron-based coatings with two types of NbC reinforcement
HF Zhang, S Zhang, H Wu, R Wang, CH Zhang… - Surface and Coatings …, 2024 - Elsevier
In this work, iron-based alloy coating without NbC (No-NbC), directly added NbC (A-NbC)
and in-situ synthesized NbC (I-NbC) reinforced composite coatings were fabricated on the …
and in-situ synthesized NbC (I-NbC) reinforced composite coatings were fabricated on the …
The influence of the pre-placed powder layers on the morphology, microscopic characteristics and microhardness of Ti-6Al-4V/WC MMC coatings during laser …
C Qi, X Zhan, Q Gao, L Liu, Y Song, Y Li - Optics & Laser Technology, 2019 - Elsevier
Abstract Ti-6Al-4V/WC metal matrix composite (MMC) coatings provide an adequate solution
for high wear resistance application of Ti-6Al-4V. Laser cladding process, which has been …
for high wear resistance application of Ti-6Al-4V. Laser cladding process, which has been …
Mechanical and thermal analyses of metal-PLA components fabricated by metal material extrusion
Metal additive manufacturing (AM) has gained much attention in recent years due to its
advantages including geometric freedom and design complexity, appropriate for a wide …
advantages including geometric freedom and design complexity, appropriate for a wide …
Sinterability of SS316, SiC, and TiN multi-material additive manufacturing via selective laser sintering
Additive manufacturing (AM) or 3D-printing (3DP) has revolutionized the manufacturing
world through its ability to rapid-printing complex designs, process a variety of materials, and …
world through its ability to rapid-printing complex designs, process a variety of materials, and …
Fabrication of GO/RGO/TiC/TiB2 nanocomposite coating on Ti–6Al–4V alloy using electrical discharge coating and exploring its tribological properties
I Taheridoustabad, M Khosravi… - Tribology International, 2021 - Elsevier
In this paper, the corrosion and wear-resistant coatings including graphene oxide (GO),
reduced graphene oxide (RGO), TiC, and TiB 2 as GO/RGO/TiC/TiB 2 nanocomposite was …
reduced graphene oxide (RGO), TiC, and TiB 2 as GO/RGO/TiC/TiB 2 nanocomposite was …
Processing and characterization of 3d-printed polymer matrix composites reinforced with discontinuous fibers
The objective of this study is to fabricate discontinuous fiber (short fiber) reinforced polymer
matrix composite material (CM) by additive manufacturing (AM) technology using single …
matrix composite material (CM) by additive manufacturing (AM) technology using single …
Designing high-temperature oxidation-resistant titanium matrix composites via directed energy deposition-based additive manufacturing
Composite material development via laser-based additive manufacturing offers many
exciting advantages to manufacturers; however, a significant challenge exists in our …
exciting advantages to manufacturers; however, a significant challenge exists in our …