Turnitin
降AI改写
早检测系统
早降重系统
Turnitin-UK版
万方检测-期刊版
维普编辑部版
Grammarly检测
Paperpass检测
checkpass检测
PaperYY检测
A two-decade odyssey in fusion-based additive manufacturing of titanium alloys and composites
SO Agbedor, H Wu, Y Ren, L Liang, DH Yang… - Applied Materials …, 2024 - Elsevier
In the past two decades, the advent of metal additive manufacturing (AM) or three-
dimensional (3D) printing technology has led to exciting breakthroughs in the metallurgy of …
dimensional (3D) printing technology has led to exciting breakthroughs in the metallurgy of …
Issues in fabrication of 3D components through DMLS Technique: A review
Abstract DMLS or Direct Metal Laser Sintering is a technique which can be classified under
an additive manufacturing (AM). In this technique, metal powders are used to manufacture …
an additive manufacturing (AM). In this technique, metal powders are used to manufacture …
Mechanical properties and corrosion resistance of laser cladding iron-based coatings with two types of NbC reinforcement
HF Zhang, S Zhang, H Wu, R Wang, CH Zhang… - Surface and Coatings …, 2024 - Elsevier
In this work, iron-based alloy coating without NbC (No-NbC), directly added NbC (A-NbC)
and in-situ synthesized NbC (I-NbC) reinforced composite coatings were fabricated on the …
and in-situ synthesized NbC (I-NbC) reinforced composite coatings were fabricated on the …
Processing, mechanical characterization, and micrography of 3D-printed short carbon fiber reinforced polycarbonate polymer matrix composite material
The objective of this research is to perform the processing and mechanical characterization
on 3D-printed high-temperature polymer (polycarbonate) reinforced with short carbon fiber …
on 3D-printed high-temperature polymer (polycarbonate) reinforced with short carbon fiber …
The influence of the pre-placed powder layers on the morphology, microscopic characteristics and microhardness of Ti-6Al-4V/WC MMC coatings during laser …
C Qi, X Zhan, Q Gao, L Liu, Y Song, Y Li - Optics & Laser Technology, 2019 - Elsevier
Abstract Ti-6Al-4V/WC metal matrix composite (MMC) coatings provide an adequate solution
for high wear resistance application of Ti-6Al-4V. Laser cladding process, which has been …
for high wear resistance application of Ti-6Al-4V. Laser cladding process, which has been …
[HTML][HTML] Mechanical and thermal analyses of metal-PLA components fabricated by metal material extrusion
Metal additive manufacturing (AM) has gained much attention in recent years due to its
advantages including geometric freedom and design complexity, appropriate for a wide …
advantages including geometric freedom and design complexity, appropriate for a wide …
Sinterability of SS316, SiC, and TiN multi-material additive manufacturing via selective laser sintering
Additive manufacturing (AM) or 3D-printing (3DP) has revolutionized the manufacturing
world through its ability to rapid-printing complex designs, process a variety of materials, and …
world through its ability to rapid-printing complex designs, process a variety of materials, and …
A review on reinforcements, fabrication methods, and mechanical and wear properties of titanium metal matrix composites
Titanium and its alloys exhibit a favorable integration of characteristics, including notable
strength and high resistance to corrosion. However, they are deficient in terms of wear …
strength and high resistance to corrosion. However, they are deficient in terms of wear …
Fabrication of GO/RGO/TiC/TiB2 nanocomposite coating on Ti–6Al–4V alloy using electrical discharge coating and exploring its tribological properties
I Taheridoustabad, M Khosravi… - Tribology International, 2021 - Elsevier
In this paper, the corrosion and wear-resistant coatings including graphene oxide (GO),
reduced graphene oxide (RGO), TiC, and TiB 2 as GO/RGO/TiC/TiB 2 nanocomposite was …
reduced graphene oxide (RGO), TiC, and TiB 2 as GO/RGO/TiC/TiB 2 nanocomposite was …
Processing and characterization of 3d-printed polymer matrix composites reinforced with discontinuous fibers
The objective of this study is to fabricate discontinuous fiber (short fiber) reinforced polymer
matrix composite material (CM) by additive manufacturing (AM) technology using single …
matrix composite material (CM) by additive manufacturing (AM) technology using single …