Halide perovskites: is it all about the interfaces?
Design and modification of interfaces, always a critical issue for semiconductor devices, has
become a primary tool to harness the full potential of halide perovskite (HaP)-based …
become a primary tool to harness the full potential of halide perovskite (HaP)-based …
Interfaces in perovskite solar cells
Rapid improvement in photoconversion efficiency (PCE) of solution processable
organometallic hybrid halide based perovskite solar cells (PSCs) have taken the …
organometallic hybrid halide based perovskite solar cells (PSCs) have taken the …
Lattice engineering for stabilized black FAPbI3 perovskite single crystals for high-resolution x-ray imaging at the lowest dose
D Chu, B Jia, N Liu, Y Zhang, X Li, J Feng, J Pi… - Science …, 2023 - science.org
Preliminary theoretical analyses indicate that lattice relaxation may be used to release lattice
strain in the FAPbI3 perovskite to warrant both high x-ray detection performance and …
strain in the FAPbI3 perovskite to warrant both high x-ray detection performance and …
Passivation of the buried interface via preferential crystallization of 2D perovskite on metal oxide transport layers
The open‐circuit voltage (Voc) of perovskite solar cells is limited by non‐radiative
recombination at perovskite/carrier transport layer (CTL) interfaces. 2D perovskite post …
recombination at perovskite/carrier transport layer (CTL) interfaces. 2D perovskite post …
Thermal evaporation and hybrid deposition of perovskite solar cells and mini-modules
The development of perovskite photovoltaics has so far been led by solution-based coating
techniques, such as spin-coating. However, there has been an increasing interest in thermal …
techniques, such as spin-coating. However, there has been an increasing interest in thermal …
Boosting long-term stability of pure formamidinium perovskite solar cells by ambient air additive assisted fabrication
Due to the high industrial interest for perovskite-based photovoltaic devices, there is an
urgent need to fabricate them under ambient atmosphere, not limited to low relative humidity …
urgent need to fabricate them under ambient atmosphere, not limited to low relative humidity …
Advanced Characterization and Optimization of NiOx:Cu‐SAM Hole‐Transporting Bi‐Layer for 23.4% Efficient Monolithic Cu(In,Ga)Se2‐Perovskite Tandem Solar …
The performance of five hole‐transporting layers (HTLs) is investigated in both single‐
junction perovskite and Cu (In, Ga) Se2 (CIGSe)‐perovskite tandem solar cells: nickel oxide …
junction perovskite and Cu (In, Ga) Se2 (CIGSe)‐perovskite tandem solar cells: nickel oxide …
Heterojunction engineering and ideal factor optimization toward efficient MINP perovskite solar cells
J Wang, S Fu, L Huang, Y Lu, X Liu… - Advanced Energy …, 2021 - Wiley Online Library
The pursuit of high power conversion efficiency (PCE) and cost‐effective perovskite solar
cells (PSCs) has spawned many innovative device structure designs. Compared with the …
cells (PSCs) has spawned many innovative device structure designs. Compared with the …
[HTML][HTML] A-site phase segregation in mixed cation perovskite
Mixed cation strategy greatly benefits the enhancement of device performance and chemical
stability. However, adverse impact also accompanies the mixed cation system …
stability. However, adverse impact also accompanies the mixed cation system …
Spontaneous enhancement of the stable power conversion efficiency in perovskite solar cells
The power conversion efficiency (PCE) of lead-halide perovskite solar cells (PSCs) is
reported to increase over a period of days after their fabrication while they are stored in the …
reported to increase over a period of days after their fabrication while they are stored in the …