[HTML][HTML] Making sustainable aluminum by recycling scrap: The science of “dirty” alloys
There are several facets of aluminum when it comes to sustainability. While it helps to save
fuel due to its low density, producing it from ores is very energy-intensive. Recycling it shifts …
fuel due to its low density, producing it from ores is very energy-intensive. Recycling it shifts …
Precipitation kinetics in metallic alloys: Experiments and modeling
Nanoscale precipitation is one of the most widely used microstructural tools to manipulate
the properties of metallic alloys, and especially to reach high strength. Optimal …
the properties of metallic alloys, and especially to reach high strength. Optimal …
Scandium in aluminium alloys
J Röyset, N Ryum - International Materials Reviews, 2005 - Taylor & Francis
A considerable part of the available literature on scandium in aluminium alloys is reviewed.
Experimental data and assessments of the binary Al–Sc phase diagram, a wide range of …
Experimental data and assessments of the binary Al–Sc phase diagram, a wide range of …
PANDAT software with PanEngine, PanOptimizer and PanPrecipitation for multi-component phase diagram calculation and materials property simulation
The newly enhanced PANDAT, integrating PanEngine, PanOptimizer and PanPrecipitation,
bridges thermodynamic calculation, property optimization, and kinetic simulation of multi …
bridges thermodynamic calculation, property optimization, and kinetic simulation of multi …
Integrated modeling of friction stir welding of 6xxx series Al alloys: Process, microstructure and properties
Compared to most thermomechanical processing methods, friction stir welding (FSW) is a
recent technique which has not yet reached full maturity. Nevertheless, owing to multiple …
recent technique which has not yet reached full maturity. Nevertheless, owing to multiple …
Loss in coherency and coarsening behavior of Al3Sc precipitates
S Iwamura, Y Miura - Acta Materialia, 2004 - Elsevier
The coarsening behavior of the Al3Sc particles in Al–0.2 wt% Sc alloy at 673–763 K is
studied on the basis of TEM observations with the numerical model. Emphasis is on the …
studied on the basis of TEM observations with the numerical model. Emphasis is on the …
[HTML][HTML] Interactions between plastic deformation and precipitation in Aluminium alloys: A crystal plasticity model
This work presents a crystal plasticity model for dynamic precipitation in aluminium alloys. It
takes into account both the influence of an evolving precipitate distribution on the critical …
takes into account both the influence of an evolving precipitate distribution on the critical …
[HTML][HTML] Modelling the spatial evolution of excess vacancies and its influence on age hardening behaviors in multicomponent aluminium alloys
Excess vacancies play crucial roles in the precipitation of age-hardening precipitates in
aluminium alloys, but their spatial evolution across grains during heat treatments is less …
aluminium alloys, but their spatial evolution across grains during heat treatments is less …
Heterogeneous Zr solute segregation and Al3Zr dispersoid distributions in Al–Cu–Li alloys
D Tsivoulas, JD Robson - Acta Materialia, 2015 - Elsevier
During the homogenisation treatment of Al alloys the Al 3 Zr phase is known to form
heterogeneously in interdendritic areas where the Zr supersaturation is low. Several types of …
heterogeneously in interdendritic areas where the Zr supersaturation is low. Several types of …
Microstructure and properties of Cu–Cr–Mg and Cu–Cr–Mg–Si alloys treated by multi-stage thermo-mechanical treatment
L Li, Y Zhang, M Ma, Y Jia, Z **ao, J Hu, Z **n… - Materials Science and …, 2023 - Elsevier
Abstract Cu-0.45 Cr-0.15 Mg and Cu-0.45 Cr-0.15 Mg-0.02 Si (wt.%) alloys exhibit excellent
comprehensive properties after treated by multi-stage thermo-mechanical treatment …
comprehensive properties after treated by multi-stage thermo-mechanical treatment …