Turnitin
降AI改写
早检测系统
早降重系统
Turnitin-UK版
万方检测-期刊版
维普编辑部版
Grammarly检测
Paperpass检测
checkpass检测
PaperYY检测
[HTML][HTML] Nano-twining and deformation-induced martensitic transformation in a duplex stainless steel 2205 fabricated by laser powder bed fusion
Duplex stainless steels (DSSs) possess desirable combinations of mechanical properties
and excellent corrosion resistance due to their composition and equilibrium microstructure of …
and excellent corrosion resistance due to their composition and equilibrium microstructure of …
Liquid metal embrittlement in laser beam welding of Zn-coated 22MnB5 steel
Despite frequent reports of liquid metal embrittlement (LME) during resistance spot welding,
no work has been done to investigate the LME sensitivity in laser beam welding (LBW) of …
no work has been done to investigate the LME sensitivity in laser beam welding (LBW) of …
On the grain boundary network characteristics in a martensitic Ti–6Al–4V alloy
The characteristics of the intervariant boundary network that resulted from the β → α^ ′ β→
α′ martensitic phase transformation in a Ti–6Al–4V alloy were studied using the …
α′ martensitic phase transformation in a Ti–6Al–4V alloy were studied using the …
[HTML][HTML] Flow stress behavior, constitutive modeling, processing map and microstructure evolution in hot deformation of Fe-7.1 Al-0.7 Mn-0.4 C-0.3 Nb alloy
The automotive industry has experienced rapid growth, with lightweight materials becoming
a significant research focus. Among these materials, low-density Fe–Mn–Al–C alloys show …
a significant research focus. Among these materials, low-density Fe–Mn–Al–C alloys show …
Dynamic recrystallization behavior and interfacial bonding mechanism of 14Cr ferrite steel during hot deformation bonding
L Zhou, W Chen, S Feng, M Sun, B Xu, D Li - Journal of Materials Science & …, 2020 - Elsevier
In this study, hot compression bonding was first applied to join 14Cr ferrite steel at
temperatures of 950–1200° C and strains of 0.11–0.51 under strain rates of 0.01–30 s− 1 …
temperatures of 950–1200° C and strains of 0.11–0.51 under strain rates of 0.01–30 s− 1 …
Flow characteristics and hot workability studies of a Ni-containing Fe‑Mn‑Al‑C lightweight duplex steel
The high temperature deformation behavior of Fe‑9Al‑10Mn‑4Ni‑0.7 C duplex steel has
been investigated in the range of temperatures 1223–1423 K and strain rates 0.001–10 s …
been investigated in the range of temperatures 1223–1423 K and strain rates 0.001–10 s …
Microstructure and mechanical properties of dissimilar friction stir lap welding between AZ31 Mg alloy and DC01 steel
AZ31 magnesium alloy and DC01 steel were friction stir lap welded (FSLW) with Z-axis force
controlled at 7.5 kN. The microstructural features and element distributions of the joint were …
controlled at 7.5 kN. The microstructural features and element distributions of the joint were …
Strain-rate dependence of the dynamic softening in a duplex stainless steel
The dynamic softening mechanism of a 2205 duplex stainless steel is comprehensively
investigated through hot compression at the temperature of 1000° C and the strain rates of …
investigated through hot compression at the temperature of 1000° C and the strain rates of …
[HTML][HTML] Temperature dependence of tensile deformation behavior and strain hardening of lean duplex stainless steels
Two lean duplex stainless steels with different manganese contents (4 and 8 wt.%) were
deformed in the tensile mode in the temperature range of 25–300° C. The deformation …
deformed in the tensile mode in the temperature range of 25–300° C. The deformation …
[HTML][HTML] The high temperature deformation behavior of a triplex (ferrite+ austenite+ martensite) low density steel
The present work deals with the high temperature deformation behavior of Fe-11.15 Mn-5.6
Al-0.07 C (wt.%) triplex ferrite-based lightweight steel in the temperature range of 800 …
Al-0.07 C (wt.%) triplex ferrite-based lightweight steel in the temperature range of 800 …